SEGGER J-Link BASE / COMPACT

J-Link BASE è un emulatore JTAG/SWD con interfaccia USB compatibile con un’ampia gamma di architetture micro

J-Link Debug Probes ➦

Emulatore JTAG/SWD con interfaccia USB

J-Link Base è un emulatore JTAG compatibile un’ampia gamma di architetture micro. Alimentato direttamente da USB, è equipaggiato con un processore RISC a 32 bit ed è in grado di comunicare ad alta velocità con le CPU target. Le caratteristiche di semplicità, unitamente alle sue performance top-level, ne fanno attualmente uno dei dispositivi più impiegati al mondo in ambito di sviluppo e produzione (programmazione flash). .

Sommando tutti i modelli di cui si compone la famiglia, ad oggi sono state vendute più di 500.000 unità, il che rende J-Link l’emulatore numero uno, e quindi lo standard de facto, per i core Arm-based.
Il J-Link è disponibile in due varianti: J-Link Base e J-Link Compact.
Il J-Link è supportato da tutti i principali IDE (Integrated Development Environment), tra cui IAR EWARM, Keil MDK, Rowley CrossWorks, Atollic True STUDIO, IAR EWRX, Renesas HEW, Renesas e2studio e molti altri.

Queste le CPU supportate da J-Link:

• Arm 7/9/11
• Cortex-A5/A8/A9
• Cortex-M0/M1/M3/M4
• Cortex-R4
• Microchip PIC32 e Renesas RX100
• RX200
• RX610
• RX621
• RX62N
• RX62T
• RX630
• RX631
• RX63N.

 

SEGGER JFlash Introduction


SEGGER J-Link Flash Breakpoint Introduction

SpecificationValue
Supported OSMicrosoft Windows 2000, XP, 2003, Vista, 7 and newer (32 bit and 64 bit versions)
Linux 
macOS 10.5 and higher
Electromagnetic compatibility (EMC)EN 55022, EN 55024
Operating temperature+5°C ... +60°C
Storage temperature-20°C ... +65 °C
Relative humidity (non-condensing)Max. 90% rH
Mechanical
Size (without cables)100mm x 53mm x 27mm
Weight (without cables)70g
Size compact device (without cables)47mm x 40mm x 14mm
Weight compact device (without cables)20g
Available Interfaces
USB interfaceUSB 2.0 (High-Speed)
Target interfaceJTAG/SWD 20-pin
JTAG/SWD Interface, Electrical
Power supplyUSB powered
Max. 50mA + Target Supply current.
Target interface voltage (VIF)1.2V ... 5V
Current drawn from target voltage sense pin (VTRef)< 25µA
Target supply voltage5V (derived from USB voltage)
Target supply currentMax. 300mA
Reset typeOpen drain. Can be pulled low or tristated
Reset low level output voltageVOL <= 10% of VIF
For the whole target voltage range (1.2V <= VIF <= 5V)
LOW level input voltage (VIL)VIL <= 40% of VIF
HIGH level input voltage (VIH)VIH >= 60% of VIF
For 1.2V >= VIF <= 3.6V
LOW level output voltage (VOL) with a load of 10 kOhmVOL <= 10% of VIF
HIGH level output voltage (VOH) with a load of 10 kOhmVOH >= 90% of VIF
For 3.6 <= VIF <= 5V
LOW level output voltage (VOL) with a load of 10 kOhmVOL <= 20% of VIF
HIGH level output voltage (VOH) with a load of 10 kOhmVOH >= 80% of VIF
JTAG/SWD Interface, Timing
Target interface speedMax. 15 MHz
SWO sampling frequencyMax. 30 MHz
Data input rise time (Trdi)Trdi <= 20ns
Data input fall time (Tfdi)Tfdi <= 20ns
Data output rise time (Trdo)Trdo <= 10ns
Data output fall time (Tfdo)Tfdo <= 10ns
Clock rise time (Trc)Trc <= 3ns
Clock fall time (Tfc)Trc <= 3ns
• Download diretto nella memoria flash dei microcontrollori supportati  
• Supports direct download into RAM and flash memory
• Supporta l'accesso concorrente alla CPU da parte di più applicazioni 
• Velocità di download fino a 1MByte/secondo
• Breakpoint illimitati nella memoria flash
• Aggiornamenti software gratuiti
• Funzionalità VCOM integrata 
• 1 anno di supporto